optoway GBS-9280Fg *********************************************************************************************************************************************************************** *********************************************************************************************************************************************************************** optoway technology inc. no .3 8, kuang fu s. road, hu kou, hsin chu industrial park, hsin chu, taiwan 303 tel: 886-3-5979798 fax: 886-3-5979737 e-mail: sales@optoway.com.tw http: // www.optoway.com.tw 12/1/2005 v2.0 1 GBS-9280Fg (rohs compliant) 5v / 1550 nm / 2.125 gb/s signle-mode gigabit interface converter (gbic) ********************************************************************************************************************************************************************** features l up to 2.5 gbps bi-directional data links l compliant with 1x / 2x fibre channel fc-pi 13.0 l compliant with gigabit interface converter (gbic) specification rev. 5.5 l 1550 nm dfb laser transmitter l 23 db power budget at least l hot pluggable module with duplex sc connector l multi-rate operation for 2.5 / 2.125 / 1.062 / 1.25 gbps l link distance up to 80 km l sca-2 host connector l single +5 v power supply l rohs compliant l differential pecl inputs and outputs l ttl rx-los output l class 1 laser international safety standard iec-60825 compliant applications l switch to switch interface l high speed interface for file servers l data storage l dual rate 1.06 / 2.125 gb/s fibre channel description the GBS-9280Fg series optical transceivers meet the gigabit interface converter (gbic) specification rev. 5.5. it satisfies the optical interface specifications defined in ieee 802.3z drift 5.0 1000 base-lx for gigabit ethernet and 1x / 2x fibre channel fc-pi 13.0. this module is designed for single-mode fiber and operates at a nominal wavelength of 1550 nm. a guaranteed minimum optical link budget of 23 db is offered which can correspond to a link distance of over 80 km (assuming worst case fiber loss of 0.25 db/km). the transmitter section uses a multiple quantum well 1550 nm dfb laser and is a class 1 laser compliant according to international safety standard iec-60825. the receiver section uses an integrated ingaas detector preamplifier (idp) mounted in an optical header and a limiting post-amplifier ic. a pecl input / output logic interface is used. ttl rx-los output simplifies interface to external circuitry. a 20-pin sca-2 host connector is used to connect the converter to the host system. laser safety this single mode transceiver is a class 1 laser product. it complies with iec-60825 and fda 21 cfr 1040.10 and 1040.11. the transceiver must be operated within the specified temperature and voltage limits. the optical ports of the module shall be terminated with an optical connector or with a dust plug. order information p/no. bit rate (gb/s) fc-pi distance (km) wavelength (nm) package temp. ( o c) tx power (dbm) rx sens. (dbm) rohs compliant GBS-9280F 2.125/1.063 200/100 80 1550 sc gbic 0 to 70 5 to 0 -23 yes absolute maximum ratings parameter symbol min max units notes storage temperature tstg -40 85 o c operating temperature topr -5 70 o c air flow 1m/sec power supply voltage vcc -0.5 6 v input voltage --- -0.5 vcc v recommended operating conditions parameter symbol min typ max units conditions power supply voltage vcc 4.75 5 5.25 v reference to gnd. power supply current i tx + i rx 200 300 ma operating temperature topr 0 70 o c air flow 1m/sec data rate 1.0625 / 1.25 2.125 / 2.5 2.5 gb/s fiber length on 9/125 m m smf 80 km @1.0625 /2.125 gb/s
optoway GBS-9280Fg *********************************************************************************************************************************************************************** *********************************************************************************************************************************************************************** optoway technology inc. no .3 8, kuang fu s. road, hu kou, hsin chu industrial park, hsin chu, taiwan 303 tel: 886-3-5979798 fax: 886-3-5979737 e-mail: sales@optoway.com.tw http: // www.optoway.com.tw 12/1/2005 v2.0 2 transmitter specifications (0 o c < topr < 70 o c, 4.75 v < vcc < 5.25v) parameter symbol min typ max units notes optical optical transmit power po 0 --- 5 dbm 1 output center wavelength l 1500 1550 1580 nm output spectrum width dl --- 1 nm -20 db width extinction ratio e r 9 --- db optical rise time t r 150 ps 20% to 80% value optical fall time t f 150 ps 20% to 80% value pout tx_disable asserted p off -35 dbm electrical differential input voltage v ih - v il 0.65 2.0 vp-p transmit fault load tx-fault load 4.7 10 k 2 transmit fault output-low v tx-fault -l 0.0 0.5 v transmit fault output-high v tx-fault-h vcc C 0.5 vcc + 0.3 v tx-disable input - low v tx-disable -l 0 0.8 v tx-disable input - high v tx-disable-h 2.0 vcc + 0.3 v tx-disable assert time t_off 10 m s tx-disable negate time t-on 1 ms time to initialize, includes reset of tx-fault t-int 300 ms tx fault from fault to assertion t-fault 100 m s tx-disable time to start reset t-reset 10 m s 1. output power is power coupled into a 9/125 m m sm fiber. 2. pull-up resistor on host vcc. receiver specifications (0 o c < topr < 70 o c, 4.75 v < vcc < 5.25v) parameter symbol min typ max units notes optical sensitivity @2.125gb/s @ ber=10 -12 sens -23 dbm 3 maximum input power pin -3 --- dbm 3 signal detect C hysteresis 1.0 --- db wavelength of operation 1200 --- 1600 nm rx-los C asserted pa --- --- -23 dbm transition: low to high rx-los C deasserted pd -31 --- --- dbm transition: high to low electrical differential output voltage rx-dat 0.37 2.0 vp-p data output rise time tr rx-dat 0.35 ns data output fall time tf rx-dat 0.35 ns receiver loss of light load rx-los load 4.7 10 k 4 loss of signal output voltage --- low rx-los l 0 0.5 v loss of signal output voltage --- high rx-los h 2.4 vcc v loss of signal assert time (off to on) t a,rx-los 100 m s loss of signal deassert time (on to off) t d,rx-los 100 m s 3. minimum sensitivity and saturation levels at ber=1e-12 for a 2 7 -1 prbs. 4. pull-up resistor on host vcc.
optoway GBS-9280Fg *********************************************************************************************************************************************************************** *********************************************************************************************************************************************************************** optoway technology inc. no .3 8, kuang fu s. road, hu kou, hsin chu industrial park, hsin chu, taiwan 303 tel: 886-3-5979798 fax: 886-3-5979737 e-mail: sales@optoway.com.tw http: // www.optoway.com.tw 12/1/2005 v2.0 3 pin assignment pin signal name sequence description 1 rx-los 2 receiver loss of signal, logic high, open collector compatible, 4.7k to 10k ohm pull-up to v cc t on host 2 r gnd 2 receiver ground 3 r gnd 2 receiver ground 4 mod-def(0) 2 ttl low 5 mod-def(1) 2 scl serial clock signal 6 mod-def(2) 2 sda serial data signal 7 tx-diable 2 transmitter disable, logic high, open collector compatible 8 t gnd 2 transmitter ground 9 t gnd 2 transmitter ground 10 tx-fault 2 transmitter fault, logic high, open collector compatible, 4.7k to 10k ohm pull-up to v cc t on gbic 11 r gnd 1 receiver ground 12 -rx-dat 1 receiver data bar, differential pecl, ac coupled 13 +rx-dat 1 receiver data, differential pecl, ac coupled 14 r gnd 1 receiver ground 15 v cc r 2 receiver +5v supply 16 v cc t 2 transmitter +5v supply 17 t gnd 1 transmitter ground 18 +tx-dat 1 transmitter data, differential pecl, ac coupled 19 -tx-dat 1 transmitter data bar, differential pecl, ac coupled 20 t gnd 1 transmitter ground a sequence value of 1 indicates that the signal is in the first group to engage during plugging of a module. a sequence value of 2 indicates that the signal is the second and last group. the two guide pins on the connector are electrically connected to the transceiver circuit ground. these two guide pins make contact with circuit prior to sequence 1 signals. module definition module definition mod-def(0) pin 4 mod-def (1) pin 5 mod-def (2) pin 6 interpretation by host 4 ttl low scl sda serial module definition protocol module definition 4 specifies a serial definition protocol. for this definition, upon power up, mod-def(1:2) appear as no connector (nc) and mod-def(0) is ttl low. when the host system detects this condition, it activates the serial protocol. the protocol uses the 2-wire serial cmos e 2 prom protocol of the atmel at24c01a/02/04 family of components.
optoway GBS-9280Fg *********************************************************************************************************************************************************************** *********************************************************************************************************************************************************************** optoway technology inc. no .3 8, kuang fu s. road, hu kou, hsin chu industrial park, hsin chu, taiwan 303 tel: 886-3-5979798 fax: 886-3-5979737 e-mail: sales@optoway.com.tw http: // www.optoway.com.tw 12/1/2005 v2.0 4 package diagram units in mm note: specifications subject to change without notice.
|
